吴 超,邓佳燕,谭 伦,胡海刚,袁德超.复合型3D打印导航模板辅助枢椎椎弓根或椎板置钉的临床研究[J].中国脊柱脊髓杂志,2018,(11):982-988.
复合型3D打印导航模板辅助枢椎椎弓根或椎板置钉的临床研究
中文关键词:  枢椎  内固定  计算机辅助设计  3D打印技术
中文摘要:
  【摘要】 目的:探讨复合型3D打印导航模板辅助枢椎椎弓根螺钉或椎板螺钉置钉的可行性及临床疗效。方法:回顾性分析2015年1月~2017年5月我院收治的32例枢椎后路内固定手术患者资料,男20例,女12例;年龄21~77岁,平均57.3±9.0岁;随访12个月以上。根据置钉方法的不同进行分组,观察组(18例)采用术前计算机模拟置钉、设计并3D打印个体化导航模板辅助枢椎椎弓根或椎板螺钉置钉;对照组(14例)采用徒手方法置入枢椎椎弓根螺钉。记录两组置钉时间、术中出血量,以Kawaguchi评价法判断螺钉置钉成功率,计算术前模拟置钉和术后实际螺钉进钉点和进钉角度在X、Y、Z轴上的偏差,并进行统计学分析。结果:所有患者均顺利完成手术,无神经、重要血管损伤等严重并发症发生。观察组共置入螺钉36枚,其中枢椎椎弓根螺钉22枚,枢椎板螺钉14枚,置钉时间31.5±6.5min,术中出血量45.0±19.2ml,Kawaguchi评价法0级32枚,Ⅰ级4枚,Ⅱ级0枚,置钉成功率100%。对照组共置入28枚椎弓根螺钉,置钉时间57.6±6.9min,术中出血量228.5±57.9ml,以Kawaguchi评价法0级18枚,Ⅰ级6枚,Ⅱ级4枚,置钉成功率85.7%;两组置钉时间、术中出血量、置钉成功率相比差异均有统计学意义(P<0.05)。术后实际钉道相对于术前模拟钉道偏差角度为0.69°±1.34°,术后实际进钉点相对于术前模拟进钉点在X、Y、Z轴上分别偏移0.50±2.13mm、0.75±2.18mm、0.43±2.39mm,偏移量与术前设计相比差异均无统计学意义(P>0.05)。结论:通过复合型3D打印导航模板辅助枢椎椎弓根或椎板螺钉置钉,能减少置钉时间及术中出血,提高置钉成功率。
Use of compound 3D printing navigation template to assist pedicle or laminar screw placement in axis
英文关键词:Axis  Internal fixation  Computer-assisted design  3D printing technology
英文摘要:
  【Abstract】 Objectives: To explore the feasibility and efficacy of the compound 3D printing navigation template in assisting the axis pedicle or laminar screw placement. Methods: 32 patients, 20 males and 12 females, aging from 21 to 77, with an average age of 57.3±9.0, with posterior internal fixation from our hospital during January 2015 to May 2017 were retrospectively analyzed; all of them were followed for more than 12 months. Among them, 18 cases of pedicle or laminar screws placement were operated by using compound 3D printing navigation template which was designed according to preoperative simulated nailing(observation group). 14 cases of pedicle screw placement were operated by free hand(control group). The blooding and nailing duration were recorded; the accuracy of screw placement was evaluated by Kawaguchi criteria; the deviation of nailing point and nailing direction between simulated screw and postoperative screw were calculated; all above parameters were statistically analyzed. Results: All patients underwent surgeries without serious complications such as nerve or blood vessel injury. A total of 36 screws were placed in the experimental group, including 22 pedicle screws and 14 laminar screws, nailing duration was 31.5±6.5min, blood loss was 45.0±19.2ml, according to Kawaguchi criteria, 32 screws were in grade 0, 4 screws in grade Ⅰ and 0 screw in grade Ⅱ, and nailing accuracy was 100%. A total of 28 screws were placed in the control group. Nailing duration was 57.6±6.9min, blood loss was 228.5±57.9ml, according to Kawaguchi criteria, 18 screws were in grade 0, 6 screws in grade Ⅰ and 4 screw in grade Ⅱ, nailing accuracy was 85.7%. There were no significant differences between the two groups in the nailing duration, blood loss and nailing accuracy(P<0.05). Angle deviation between postoperative nailing and simulated nailing was 0.69°±1.34°; the deviation between the postoperative nailing point and the simulated nailing point on the X, Y and Z axes was 0.50±2.13mm, 0.75±2.18mm, 0.43±2.39mm, respectively. There was no significant difference of above deviations between postoperative and preoperative design(P>0.05). Conclusions: Use of compound 3D printing navigation template in assisting in the placement of pedicle screws or laminar screws can reduce nailing duration and blood loss and improve nailing accuracy. It is an alternative measure for arthroscopic pedicle screw placement failure.
投稿时间:2018-06-03  修订日期:2018-08-03
DOI:
基金项目:四川省重点科技计划项目(编号:2016JY0108);四川省卫计委科研课题(编号:17PJ144);四川省医学会科研课题(编号:2015GK016)
作者单位
吴 超 四川省自贡市第四人民医院骨科 643000 
邓佳燕 四川省自贡市第四人民医院数字医学中心 643000 
谭 伦 四川省自贡市第四人民医院骨科 643000 
胡海刚  
袁德超  
摘要点击次数: 3358
全文下载次数: 2131
查看全文  查看/发表评论  下载PDF阅读器
关闭